A-JOINT® READY PRO is a ready-to-use, vacuum-packed paving joint mortar, specially developed for gardening and landscaping. It is water-permeable, frost-resistant and cures on contact with atmospheric oxygen.
A-JOINT® READY PRO is designed for medium traffic loads of up to 7.5 t and, thanks to its special sand grain size, can also be used in narrow joints from 3 mm in width.
A-JOINT® READY PRO can be used as a robust, all-round jointing solution for paved surfaces on garage driveways, courtyards and commercial areas.
VARIANTE
Neutral
Basalt
Stone grey
A durable, robust jointing solution for gardening and landscaping, suitable for usage category N2+
Weed-free, water-permeable, frost- and de-icing salt resistant
For joint widths of 3 mm
For joint depths of 25 mm
Ready-mixed and vacuum-packed, immediately "READY" for processing
walkable after 24 hours, trafficable after 6 days. Low temperatures and high humidity may prolong complete curing
Delivery form
25 kg PCR buckets made from recycled plastic
Shelf life
24 months store dry, frost-free and protect from direct sunlight
Compressive strength
17,5 N/mm² laboratory value, construction site value 15,3 N/mm²
Flexural strength
7,7 N/mm² laboratory value, construction site value 6,8 N/mm²
Static modulus of elasticity
3480 N/mm²
Solid mortar density
1,63 kg/dm³
Water permeability
3,90 x 10-3m/s (with 10% joint content approx. 10 l/m²/min depending on compaction)
Calculator for this product
Instructions for use
1
Pre-wetting
2
Filling the joints
3
Sweep off
4
Ready
Processing instructions
Preparing the site:
The joints must be cleared of weeds, roots and loose parts to a depth of at least 25 mm (2/3 of the stone
height for traffic load). The surface to be grouted must be freed from all dirt. Adjacent areas that are not
to be grouted should be masked or covered. To avoid settling and loose stones, we recommend a
permanently water-permeable and load-bearing substrate in accordance with the subsequent load
(pay attention to the current standards and guidelines). We generally recommend the bonded
construction method.
Pre-wetting:
Pre-wet the entire surface extensively. Higher surface temperatures and absorbent, open-pored stones
require more intensive pre-wetting. Generally, use clean and cold water.
Filling the joints:
Remove the vacuum bag from the bucket, cut it open and spread the compound evenly over the well
pre-wetted surface. Work the paving joint mortar intensively into the joints with a broom or rubber
squeegee. The joints must be completely filled and compacted. In order to increase the strength of the
joint, the fresh mortar can be elutrified using a fine water spray jet. Also narrower joints can be filled
more easily with this method. Avoid standing water in the joints during application. Sunken joints must
be refilled with fresh paving joint mortar immediately.
Cleaning the surface:
Directly after filling the joints, carefully clean the stone surface with a fine broom diagonally across the
joint. Remove all residues of the paving mortar from the stone surface. Do not reuse any material that
has been swept off. Be aware that chamfers (bevelling of the side edges) on slabs and pavers must be
exposed.
After-treatment:
Protect the freshly jointed surface from continuous or heavy rain for 12-24 hours. We recommend construction foil or tarpaulins as rain protection. These can be laid directly on the surface. At temperatures around 20°C, the surface can be walked on after 24 hours and driven on after 6 days. Low temperatures and high humidity can extend the complete curing time up to several weeks. Due to raw material light sanding of the mortar surface is possible. Cleaning work (high-pressure cleaner max. 100 bar, min. 30 cm distance) may be carried out after 7 days at the earliest.
Resin film: After jointing with A-JOINT®READY PRO, a thin resin film remains on the stone surface, which intensifies the stone colour and protects it from dirt. This resin film usually disappears over time due to weathering and use of the surface. In case of doubt, create a small sample surface before jointing the entire area. The resin film is not a design defect, as neither the quality nor the functionality of the joint is affected.
Application notes: Use A-JOINT®READY PRO only with a stable, load-bearing and permanently water-permeable substructure or a slope of at least 2%. In this regard, take into account the current regulations for the construction of terraces and paths. Do not use in permanent wet areas e.g. pools, fountains or drains. A-JOINT®READY PRO has an unique smell which disappears over time after complete hardening. Application is recommended only in well ventilated outdoor areas. We draw attention to the wearing of adequate protective work clothing. Shoes and tools must be free from dirt and should be cleaned with water during and after application.
Regularly remove dirt, leaves and moss from the joint surface.
All filler materials are natural products and are subject to natural colour variations. Our information is based on experiential values and the current levels of knowledge in science and practice, however they are not binding and have no legal force.
To provide the best experiences, we use technologies like cookies to store and/or access device information. Consenting to these technologies will allow us to process data such as browsing behavior or unique IDs on this site. Not consenting or withdrawing consent, may adversely affect certain features and functions.
Functional
Always active
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
Preferences
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
Statistics
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
Marketing
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.