Contact us Contact us
EN
A-JOINT READY PRO
All products A-JOINT READY PRO

A-JOINT READY PRO

Steps Calculator

A-JOINT® READY PRO is a ready-to-use, vacuum-packed paving joint mortar, specially developed for gardening and landscaping. It is water-permeable, frost-resistant and cures on contact with atmospheric oxygen. A-JOINT® READY PRO is designed for medium traffic loads of up to 7.5 t and, thanks to its special sand grain size, can also be used in narrow joints from 3 mm in width. A-JOINT® READY PRO can be used as a robust, all-round jointing solution for paved surfaces on garage driveways, courtyards and commercial areas.

VARIANTE

Basalt
Neutral
Stone grey
A durable, robust jointing solution for gardening and landscaping, suitable for usage category N2+
Weed-free, water-permeable, frost- and de-icing salt-resistant
For joint widths of 3 mm or more
For joint depths of 25 mm or more
Pre-mixed and vacuum-packed, immediately ‘READY’ for use
Can be applied when the ground temperature is 5°C or above
Can be used in light rain; no cement residue
System
1-komponentiger Kunstharzmörtel / Pflasterfugenmörtel
Verarbeitungszeit bei 20°C
ca. 30 Minuten nach öffnen des Vakuumbeutels
Verarbeitungstemperatur
> 5°C, max. 30°C
Freigabe der Fläche bei 20°C
nach 24 Std. begehbar, nach 6 Tagen befahrbar. Niedrige Temperaturen und hohe Luftfeuchte können die vollständige Aushärtung verlängern
Lieferform
25 kg PCR-Eimer aus recyceltem Kunststoff
Lagerfähigkeit
24 Monate trocken, frostfrei lagern und vor direkter Sonneneinstrahlung schützen
Druckfestigkeit
17,5 N/mm² Laborwert, Baustellenwert 15,3 N/mm²
Biegezugfestigkeit
7,7 N/mm² Laborwert, Baustellenwert 6,8 N/mm²
Statisches Elastizitätsmodul
3480 N/mm²
Festmörteldichte
1,63 kg/dm³
Wasserdurchlässigkeit
3,90 x 10-³ m/s (bei 10 % Fugenanteil ca. 10 l/m²/min je nach Verdichtung

Calculator for this product

Instructions for use

  1. 1

    Preparation

    The joints must be cleared of all weeds, roots and loose material to a depth of at least 25 mm (in the case of traffic loads, 2/3 of the stone height). The surface to be jointed must be cleared of all dirt . Adjoining areas that are not to be grouted should be masked off or covered. To prevent settlement and loose stones, we recommend a permanently water-permeable and load-bearing sub-base appropriate to the anticipated load (please observe the current standards).

  2. 2

    Pre-soaking

    Thoroughly pre-wet the entire surface. Higher ground temperatures and absorbent, open-pored rock require more intensive pre-wetting. As a general rule, clean, cold water should be used.

  3. 3

    Filling the joints

    Remove the vacuum bag from the bucket, cut it open and spread the mixture evenly over the thoroughly pre-wetted surface. Work the paving joint mortar vigorously into the joints using a broom or rubber trowel. The joints must be completely filled and compacted. By lightly spraying the fresh mortar with a fine mist of water, you will increase the strength of the joint, and narrower joint widths can be filled more easily. Avoid standing water on the surface during application. Joints that have sagged must be filled immediately with fresh jointing compound.

  4. 4

    Fertig

    Fertig

Stay Connected

Let's get in touch !

We're here to assist you with any inquiries.

Talk to an expert